Stamped Concrete Supplies in Tulsa

Stamped Concrete is a very popular choice for Tulsa & Oklahoma City driveways, sidewalks and walkways. 

Stamped Concrete brings color and texture to plain concrete and allows for textures and 3-D looks for residential and commercial concrete surfaces. Below you will find the stamped concrete supplies that we offer to help you color and texture your concrete surface in Tulsa, as well as an in depth ‘how-to’ for stamping concrete for those of you that are newer to the industry:

colors-color-hardener-beautycreteColor Hardener

Our Color Hardener is used to topically color the wet surface of freshly poured concrete in Tulsa. Our Color Hardener is available in 30 standard colors and is a great alternative to integral coloring of concrete should your customer desire a more ‘extreme’ colored surface underneath a pigmented sealer as is a fairly typical occurrence among clients in the greater Oklahoma City area.  If you are unsure how to apply Color Hardener, read the instructions sheet by clicking on the image to the left.

Coverage Rate:  100 sq. ft. per pail

Color Chart: Click Here

colors-powder-release-beautycretePowder Release

Powder Release is used as a secondary coloring system for stamped concrete in Tulsa. Our powder release is available in 30 standard colors. The release agent is needed while stamping your surface to ‘release’ the wet concrete from your stamping tool. Using a tinted powder release will add more depth to the texture of your stamped concrete job.  See the directions below for details on when in the stamping process this product would be used.

Coverage Rate: 1,000 sq. ft. per pail

colors-integral-color-beautycreteIntegral Color

Integral Color is used as a primary coloring system for stamped concrete in Tulsa. Our integral color is available in 20 standard colors, but can be custom blended per request. Even if you plan on using a pigmented sealer on top of your stamp job, it’s always a good idea to integrally color the concrete to avoid the appearance of unwanted grey areas if and when the slab becomes damaged due to the extreme climate and moisture changes in Oklahoma.

Coverage Rate: Varies By Color, Strength of Pigment, Sold by the cubic yard (speak with your rep for details on selecting the correct amount of pigment to match the color chart)

Liquid Release

Liquid Release is a clear release agent for concrete stamping tools. It can be used with both skin and grouted concrete stamping tools.

Coverage Rate: 1,200 sq. ft. per pail

How do you stamp fresh poured concrete?

Stamped Concrete Installation

1. Forming: Install formwork the same as any other concrete pour. Drive the stakes even or below the top of the formwork and make sure the formwork is square, especially for a square pattern.
2. Prep Work: Protect all surrounding areas with plastic, (ie. walls, shrubs, fences, etc.)Note: If using integral coloring in the truck, throw (1) SureCrete custom blended (By Sack mix) biodegradable bag per yard in the truck and follow approved mixing practices. (Step (4) is now optional)
3. Pour Concrete: Pour, screed and float the same as any other concrete pour.
4. Color Hardener: Roll the unopened Color Hardener bucket on its side. (Open and break any clumps by hand.) Broadcast the Color Hardener evenly on the surface without leaving any piles. (Broadcast about 75% of the Color.) Once the bleed water ceases and the color fully wets up. (Darkens up.) Use a wood, or mag float to work the color into the surface & edge it. Apply a 2nd coat of C/H, filling in any uncolored areas. When it wets up, float it in &edge it. Finish trowel or Fresno the surface to remove any low areas or trowel marks.
5. Release: Apply a thin even coat of Powder Release, using the same broadcast method as the C/H.(You can also use a masons brush) Only apply approximately (2) rows ahead of stamping. (Never trowel release.)
6. Stamping: Place stamp tools on the areas with release powder and walk them in until full texture is achieved (Use an impact tool “tamper” when necessary.) Continue running stamps, by lifting the earliest stamp placed and setting it in sequence. (Always stamp with a tool against a toolbefore moving) If the desired texture is not achieved, reset the stamp in the same position, and apply proper pressure. Use flexible stamps, & touch up mats against walls & columns. Avoid creating a vacuum when lifting tools by curling in the corners or edges of tools while lifting. Periodically check stamp alignment & adjust if necessary.
7. Detailing: After lifting tools use a chisel, S-tool or grout-wheel to fix any material that has squeezed up between stamps, or to continue any grout lines. Use the touch up mats where texture is lacking.
8. Washing off & Saw Cuts: Wash off the excess release the following day with a garden hose. (During cooler weather wait longer for the concrete to cure.) Normally concrete decides where it is going to crack the 1st 12-24 hours after the pour. Cut your control joints in ASAP ¼ the depth of the slab.(Maintain common concrete practices) Use a hand Grinder or chisel to touch up any grout lines, or squeeze joints not fixed during the stamp process.
9. SCR Wash: (1-3 Days later depending on temperature) Mix 1 part SCR to 5 parts water & spray the solution with an acid resistant pump sprayer. Scrub the slab with a broom (Your goal should be to get the heavy release off the tops of the stones, slates etc., areas where foot trafficwould touch) Rinse thoroughly (Do not allow SCR to dry on surface) & try to achieve even color throughout the job. Repeat if necessary. (Release powder can be a bond breaker for the seal & should only be left in the recessed areas)
10. Release & Seal: When the surface is fully dried, use a paint brush,(cut down to a stiff bristle) to rub dry release powder, into any joints that need contrasting color. With a high velocity leaf blower, (preferably electric) blow off the extra release. Use a solvent resistant roller cover to seal the surface with one thin coat of SureCrete Clear Seal. Apply a second (thin coat) if needed. SureGrip can be added to the top coat of clear seal to help with a non slip surface.

Beauty Crete Supply is located in Tulsa, Oklahoma and we offer concrete supplies for restoring, resurfacing and sealing concrete driveways, sidewalks, foundations, walls, and commercial floors. We supply the greater Tulsa and Oklahoma City area with decorative concrete supplies such as: Ada, Altus, Alva, Anadarko, Antlers, Apache, Ardmore, Atoka, Barnsdall, Bartlesville, Beaver, Beggs, Bethany, Bethel Acres, Bixby, Blackwell, Blanchard, Boise City, Bridgeport, Bristow, Broken Arrow, Broken Bow, Byng, Cache, Catoosa, Cedar Valley, Centrahoma, Chandler, Checotah, Cherokee, Chickasha, Choctaw, Chouteau, Claremore, Cleveland, Clinton, Coalgate, Collinsville, Comanche, Commerce, Coweta, Crescent, Cushing, Davis, Del City, Dewey, Drumright, Duncan, Durant, Edmond, El Reno, Elgin, Elk City, Enid, Erick, Eufaula, Fairfax, Fairview, Fort Gibson, Frederick, Garber, Geary, Glenpool, Goldsby, Grandfield, Grove, Guthrie, Guymon, Haileyville, Harrah, Hartshorne, Haskell, Healdton, Heavener, Hennessey, Henryetta, Hinton, Hobart, Holdenville, Hollis, Hominy, Hooker, Hugo, Idabel, Inola, Jay, Jenks, Jones, Kellyville, Kingfisher, Kingston, Konawa, Krebs, Langston, Lawton, Lexington, Lindsay, Locust Grove, Lone Grove, Madill, Mangum, Mannford, Marietta, Marlow, Maud, McAlester, McLoud, Medford, Miami, Midwest City, Minco, Moore, Mooreland, Morris, Muskogee, Mustang, New Cordell, Newcastle, Newkirk, Nichols Hills, Nicoma Park, Noble, Norman, Nowata, Oilton, Okarche, Okeene, Okemah, Oklahoma City, Okmulgee, Oologah, Owasso, Panama, Pauls Valley, Pawhuska, Pawnee, Perkins, Perry, Picher, Piedmont, Pocola, Ponca City, Pond Creek, Poteau, Prague, Pryor, Purcell, Quinton, Ringling, Roland, Rush Springs, Sallisaw, Salina, Sand Springs, Sapulpa, Sayre, Seiling, Seminole, Shawnee, Shidler, Skiatook, Slaughterville, Snyder, Spencer, Sperry, Stigler, Stillwater, Stilwell, Stratford, Stroud, Sulphur, Tahlequah, Talihina, Tecumseh, The Village, Thomas, Tishomingo, Tonkawa, Tulsa, Tupelo, Tuttle, Union City, Verdigris, Vian, Vinita, Wagoner, Walters, Warner, Warr Acres, Watonga, Waukomis, Waurika, Waynoka, Weatherford, Wetumka, Wewoka, Wilburton, Wilson, Woodward, Wynnewood, Yale and Yukon with color hardeners, powder release agents, concrete color, technical support, and stamped concrete instructions and training.